Hexagon Tree Skirt - Tutorial

Hi friends! Continuing my Hexie Holidays projects with today's tutorial showing you how to create a lovely Hexagon Tree Skirt!


This tutorial uses the same basic steps of applying hexies to your project as my Hexagon Mini Quilt. 

Materials needed:

  • Main fabric 32" x 32" square - Essex Linen in Black
  • Border fabric 4 strips 5"  WOF (width of fabric) - Timeless Treasures Soho White
  • Batting piece 45" x 45" - I used precut crib sized batting
  • Backing fabric 42" x 42" (at least) - Soho Solids White
  • Binding fabric - 6 strips 2.5" WOF (width of fabric) - Soho Solids White
  • 4 strips of ribbon cut 12"
  • Spray basting glue, or pins for basting quilt
  • Thread - white for your main quilting, red for quilting around your hexies
  • 60 hexies - for these you will need 60 paper templates & 60 squares of scrap fabric cut 2.5"
  • Aleene's Fabric Fusion Glue
  • Scissors, rotary cutter, acrylic ruler, cutting mat, iron, pen, clear bowl or cup

hexietree8Step 1:

Take your center piece and add your border fabric on the top and the bottom of your square, then trim to even. Now add your border fabric to the right and left sides, then trim to even. What you have should now look like the above picture.


Step 2:

Take your top that you just finished and layer it over your batting and your backing fabric creating a quilt sandwhich. Using your method of basting - spray baste or pins - baste your fabrics to prepare for quilting. Use the method of quilting that you enjoy! I am not a free motion quilter so I just stick to straight line quilting. Any way you choose will look great.


Step 3:

Take your quilted square to your cutting mat and using a rotary cutter and ruler measure out 4 inches for your cut. This will even up your square and trim away any rough edges and batting.


Step 4:

Now you can lay out your square and make sure every thing is even.


Fold your square in half and in half again, find your middle corner and using a clear bowl/cup draw a line around where you will make your cut. I like using a clear bowl just so I can see how my fabric is lined up underneath.  **If you have a fake tree like I do - DO NOT cut a circle as large as I did! A small hole will work fine. I am telling myself that this will be a good tree skirt to use in the future on a live tree because the hole is too large for my fake tree :) Going along the line that you drew cut your circle shape out.


Your quilt will now look like this in the middle **And if you were smart the hole will be much smaller :)

Side note: cutting a hole in the middle of something that you just spent who knows how long quilting is quite painful....


Step 5:

Take your square and fold into half once. Using your scissors cut along the fold like shown above creating the opening to your tree skirt. Remember to only cut one side!


This is what your tree skirt should look like at this point.


Step 6:

Take your 60 hexies, more or less if you change the size of your quilt and press them with your iron on high heat/steam to set the hexie. For more detailed instructions on this process please see this earlier post and for complete instructions on how to make a hexie I highly recommend Ellison Lane's video tutorial.


Lay your 60 hexies around the line that connects your main fabric to your border fabric. The corner pieces will be at an angle with the top two side points of the hexie on the line. This will allow all 60 pieces to fit. Play around with this layout before gluing to make sure everything fits nicely.


Step 7:

Now you will start to attach the hexies to the fabric. Starting with any hexie, snip the back thread and remove, remove the paper template and apply a thin line of glue around the inside border of your hexie.


Press firmly on the hexie you are gluing down. The uneven surface of the quilting is sometimes hard to glue on when using a very small amount of glue.


Step 8:

Back at your machine it is now time to sew down the hexies. The easiest way I have found to do this is to stitch around one side of the hexies first, going around the entire tree skirt. Once you finish one side, flip the tree skirt around and sew around the other side. I also found that rolling the tree skirt up was the easiest way to handle the size because it does become cumbersome.

Step 9:

Finally time to add your binding and ribbon to finish off the project! I usually bind my projects the same way I do my quilts with my machine. Feel free to machine bind or bind by hand! If you are new to binding a quilt, there are several videos online showing how to do so that are very helpful.

Take your time and pin a lot when going around the middle circle. That seemed to be the toughest to sew.


For my ribbon I just made a tie with some left over binding fabric I stitched closed. You can use ribbon, string or fabric for your tree skirt closure. For placement of the ribbon I placed one about 2 inches from the middle circle and then one 3 inches from the outside edge. Stitch the ribbon in place on the underside of your tree skirt and finish the edges with a no fray glue  (fray check) if using ribbon.

You are finished! Here are some more pictures of the finished project, if you make this tree skirt please share with us your work! On Instagram or Twitter: #hexieholidays Or tag me in your post @modernhandcraft.



If you end up making the tree skirt hole a little too large, just place a piece of fabric over the tree base and then wrap with tree skirt.



Here you can see how the corner pieces fit into the layout with the top two side points on the line.


Follow along with future projects and posts with Bloglovin.

Thanks for stopping by friends!